TX1000 Telemetry Transmitter Building Block Video Ltd 17 Apex Park Diplocks Industrial Estate Hailsham, East Sussex, BN27 3JU, UK Tel: + 44 (0) 13
TX1000 manual V7 June 09 Camera Selection A camera may be selected onto the controlled monitor by pressing the relevant numbered camera key: 1 2
TX1000 manual V7 June 09 Press the Program key to enter the menu and select ‘9’. The on screen prompt "Seq Delay" appears, inviting the
TX1000 manual V7 June 09 Keypad functions The keypads should not be connected or disconnected from a "live" working unit, as this may d
TX1000 manual V7 June 09 Autopan - Press, LED lights up and autopan motor starts. Pressing Left or Right stops Autopan Lights - Latching
TX1000 manual V7 June 09 Maximum Camera Number To set the Maximum camera number, Press Program, then enter 15 followed by the maximum number of c
TX1000 manual V7 June 09 Patrol settings There are two preset patrols that can be started by the TX1000. To activate: Press and hold the Patro
TX1000 manual V7 June 09 Setting a delay for Patrol 1: PROGRAMMenuOption7Then?Delay number Setting a delay for Patrol 2: PROGRAMMenuOption8The
TX1000 manual V7 June 09 RS422 TELEMETRY The TX1000 matrix has a single RJ45 connector that is used to control BBV RS422 telemetry receivers or a
TX1000 manual V7 June 09 TX1000 Series Alarm Input Option Alarm Inputs Alarms activate on opening of contacts. Connect each alarm pair to a vol
TX1000 manual V7 June 09 Enabling/Disabling the Alarm package The alarm package can be enabled/disabled; for example at night when the building i
TX1000 manual V7 June 09 Contents Important – Before you install 3 TX1000 Telemetry Transmitter – an Introduction 4 Unpacking 5 A simple TX1
TX1000 manual V7 June 09 The length of time the contacts close is also programmable. To program the length of time the contacts close: First det
TX1000 manual V7 June 09 - Blank for your notes - 21
TX1000 manual V7 June 09 Appendix Useful Keystrokes: Software version Hold hash and tap the 10 key to make the software version number, number
TX1000 manual V7 June 09 TX1000 Alarm Program Table Site Name Date PROGRAM 11 INPUT NUMBER CAMERA NUMBER PRESET PROGRAM
TX1000 manual V7 June 09 Extend your BBV Warranty from 12 months to 3 years As of the 1st September 2008 BBV have offered our customers the op
TX1000 manual V7 June 09 IMPORTANT Before you install: Please read the following points before servicing or installing. Pre-installation checks -
TX1000 manual V7 June 09 TX1000 Telemetry Transmitter – Introduction The TX1000 is a simple to use telemetry transmitter for multi-camera CCTV sy
TX1000 manual V7 June 09 Unpacking Inspect the packaging for signs of damage. If damage has occurred, advise the carriers and/or the suppliers i
TX1000 manual V7 June 09 RX100dome camera4 local alarmsSTATICstatic cameraRX200Static camera withlights/wash/wipeRX200Simple AC pannerRX300AC P/
TX1000 manual V7 June 09 Technical Specification Power supply 9V dc 500mA Inputs Data input to base unit is RS232 via 9-pin D connector RS232 p
TX1000 manual V7 June 09 Layout of the TX1000 keypad 9V ac/dc Video in Video out Installing the TX1000 Matrix & Keypad 1. Mount the base
TX1000 manual V7 June 09 Status LED The STATUS LED should flash and the monitors should show the video from Camera 1 on power up. If the LED is
Comments to this Manuals